日韩人妻无码精品二专区,国产成人免费高清直播下载,一本一道久久综合久久,超碰aⅴ人人做人人爽欧美

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:2216
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention jsance.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(jsance.com)  Su ICP 15043207-1 Design :25318.cn

精品国产一区二区三区av片| 免费人成视频在线| 熟女性饥渴一区二区三区| 欧美牲交a欧美牲交aⅴ一| 青草影院内射中出高潮| 国产精品嫩草影院永久| 成年免费A级毛片高清香蕉| 亚洲AV成人精品网站在线播放| 国产三级片在线观看| 999久久久精品国产消防器材| 亚洲S久久久久一区二区| 老熟女高潮喷了一地| 少妇搡bbbb搡bbb搡aa| 成人欧美一区二区三区黑人| 19禁无遮挡啪啪无码网站性色| 久久久久精品国产亚洲AV电影| 国产精品免费无遮挡无码永久视频| 久久九九国产精品怡红院| 牲高潮99爽久久久久777| 久久亚洲sm情趣捆绑调教| 欧美jizz18性欧美| 久久久久亚洲av无码专区首jn| 新区乱码无人区二精东| 狠狠噜天天噜日日噜无码| 亚洲AV男人的天堂在线观看| 男人j放进女人p全黄动态图| 国产毛片毛多水多的特级毛片| 中文字幕日韩三级片| 女性喷液过免费视频| 欧美性色欧美A在线播放| 国产成人精品A视频| 国产精品186在线观看在线播放| 日本一本之道高清不卡免费| 成人午夜国产内射主播| 高清不卡一区二区三区| 精品国产乱码久久久软件下载| 亚洲精品无码av人在线观看| 嫩bbb槡bbbb槡bbbb| 天天色影网| 亚洲色AV性色在线观无码| 欧美国产成人精品一区二区|